Honestly, I would have thought it to be the other way around. If I shut the port on our office Cisco that my phone is connected to, the phone turns off. Regards, Nick Pratley Senior Network Operator[image: Facebook] <https://www.facebook.com/ServersAustralia>[image: @serversau on Twitter] <https://twitter.com/serversau>[image: Servers Australia] Ask us about web hosting... [image: QMS Certified ISO 9001 Compliant]Phone: +61 2 8115 8817 Network Ops: +61 2 8115 8850 Main Switch: +61 2 8115 8888 Web: www.serversaustralia.com.au 11/6 Reliance Drive, Tuggerah NSW 2259 PO Box 3187, Tuggerah NSW 2259 SYDNEY | BRISBANE | PERTH | MELBOURNE | NEW ZEALAND *Notice:* This message may contain private and confidential information intended only for the recipients. If you have received this message in error please delete immediately and notify the sender. Any distribution or reproduction of this message is prohibited. The views & opinions expressed in this email are NOT necessarily those of Servers Australia. On Tue, Aug 4, 2015 at 2:59 PM, Paul Julian <paul@oxygennetworks.com.au> wrote:
Good on you Nick, thanks mate, I thought it would be pretty crazy to disable power when disabling the interface for data, but hey, Mikrotik are known to a be a bit quirky sometimes !
I will give it a try
Thanks !
Regards Paul
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Nick Pratley Sent: Tuesday, 4 August 2015 2:18 PM To: MikroTik Australia Public List Subject: Re: [MT-AU Public] POE Interface and Disable command
Hey Paul,
Just tested with two sitting on my desk doing nothing else at present. Was curious about this.
You're in luck. All 5 interfaces disabled - however the device is still powered.
Your mileage may vary though.
Regards,
Nick Pratley Senior Network Operator[image: Facebook] <https://www.facebook.com/ServersAustralia>[image: @serversau on Twitter] <https://twitter.com/serversau>[image: Servers Australia]
Ask us about web hosting... [image: QMS Certified ISO 9001 Compliant]Phone: +61 2 8115 8817 Network Ops: +61 2 8115 8850 Main Switch: +61 2 8115 8888 Web: www.serversaustralia.com.au
11/6 Reliance Drive, Tuggerah NSW 2259 PO Box 3187, Tuggerah NSW 2259
SYDNEY | BRISBANE | PERTH | MELBOURNE | NEW ZEALAND
*Notice:* This message may contain private and confidential information intended only for the recipients. If you have received this message in error please delete immediately and notify the sender. Any distribution or reproduction of this message is prohibited. The views & opinions expressed in this email are NOT necessarily those of Servers Australia.
On Tue, Aug 4, 2015 at 2:06 PM, Paul Julian <paul@oxygennetworks.com.au> wrote:
Stupid question perhaps....but, I have access into a CPE via the wireless link, and in good Mikrotik fashion the router I have on the other side of the CPE, also a MT, has auto negotiated at 10M FULL, so I need to disable the interface and re-enable it from the CPE side, but, the CPE is powered using POE on that same interface.
Sooo, if I disable the Ethernet interface will it lose power or is the POE totally separate from the data side of the interface, I am pretty sure it is but before dropping this interface I Want to be 100% sure as it's a long drive to re-enable it J
Thanks Paul _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au