Actually that's a good point - I don't need to reboot my mAP's to
dongles in.. Maybe it's a CRS oddity? :)
On 25 November 2015 at 23:43, wrote:
I'll try plugging it in and then powering on in the morning but I was able to plug it into a hAP, mAP and a CCR1009 and it was recognised immediately with out reboot. All running 6.33 or 6.33.1.
From: Damien Gardner Jnr Sent: Wednesday, 25 November 2015 11:10 PM To: MikroTik Australia Public List
Hmm, the MF823 'just works' on the CRS109 for me. When you say 'plug it in', you're power cycling the CRS after plugging it in yeah? While you can power cycle the USB port to reset a locked up LTE dongle, the dongle must be plugged in when the CRS boots, for it to see it in the first
From some reading in the forums, make sure your power supply that is feeding the MT unit is up to task(e.g higher amp unit), as the current draw from the USB modem can be significant. Cheers Greg ----- Original Message ----- From: "MikroTik Australia Public List" To:"MikroTik Australia Public List" Cc: Sent:Wed, 25 Nov 2015 21:15:43 +0000 Subject:Re: [MT-AU Public] CRS109-8G-1S-2HnD-IN usb port not working with LTE So I power cycled the CRS with the modem plugged in and it came up when the router had rebooted. BUT… it was very unstable it kept dropping the lte interface and the dhcp lease kept getting renewed so it appears that it is not all plain sailing. It does not surprise me that the 2011is the same as it has the same chipset I believe. From: Jason Hecker (Up & Running Tech) Sent: Thursday, 26 November 2015 5:26 AM To: MikroTik Australia Public List The same issue exists for the RB2011, you need to plug the module in and then power it up. I suspect it puts the USB port in the right mode (host). On 25 November 2015 at 23:49, Damien Gardner Jnr wrote: plug the place..
On 25 November 2015 at 22:34, Andrew Gilbett wrote:
Hi Guys,
I have a Huawei E8372 that works on a hAP just fine.
But when I plug it into a CRS109-8G-1S-2HnD-IN it does not
register as an
LTE device even though both devices are running the same firmware. Nor does it work as a PPP device on either mikrotik.
Has any one had luck getting the USB port to work on the CRS?
Any help would be very happily received!
Thanks Andrew _______________________________________________ Public mailing list Public@talk.mikrotik.com.au
http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
--
Damien Gardner Jnr VK2TDG. Dip EE. GradIEAust rendrag@rendrag.net - http://www.rendrag.net/ -- We rode on the winds of the rising storm, We ran to the sounds of thunder. We danced among the lightning bolts, and tore the world asunder _______________________________________________ Public mailing list Public@talk.mikrotik.com.au
http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au
http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
--
Damien Gardner Jnr VK2TDG. Dip EE. GradIEAust rendrag@rendrag.net - http://www.rendrag.net/ -- We rode on the winds of the rising storm, We ran to the sounds of thunder. We danced among the lightning bolts, and tore the world asunder _______________________________________________ Public mailing list Public@talk.mikrotik.com.au
http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
-- _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au