Hahah, ok, sorted that. Seems I've been fat-fingering my default route since day one... Was just BGP making it a non-issue ;) I now have a default route, my ip4/6 tunnels to the US have come up, along with their BGP sessions. And I can now traceroute to my ipv6 ip's.. BUT.. Neither of my domestic V6 tunnels have come up! What the! Oh well, that's fixed for tonight, I'll email both upstreams and get them to check their ends :) Thanks for the help today folks :) Now I have to remember where I bought my CCR (wasn't through mike unfortunately - I needed it for 3 days later, and he didn't have any until the following week at the time), and get in touch to send it back for a warranty job! Regards, Damien On 4 March 2015 at 18:11, Damien Gardner Jnr <rendrag@rendrag.net> wrote:
Though the thing I don't understand, is that I can ping the gateways - RouterOS is just refusing to route via them?
On 4 March 2015 at 17:40, Damien Gardner Jnr <rendrag@rendrag.net> wrote:
Ohhhh, even when esxi is just passing the vlans through and not doing any ipv6 itself?
In that case, looks like i'm bringing up ANOTHER router in xenserver just to do v6 :-p argh!
On 4 March 2015 at 17:38, Tim Warnock <timoid@timoid.org> wrote:
On a 2950, use ESXI5.0
Don't use 5.1 or higher or IPv6 breaks.
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Alex Samad - Yieldbroker Sent: Wednesday, 4 March 2015 4:37 PM To: MikroTik Australia Public List Subject: Re: [MT-AU Public] CCR1009 crashing - how to debug?
I had a very hard time getting routeros in a vm, use a trunk port. Fell back to splitting off the vlans to individual interfaces.
I noticed very strange things happening ..
A
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Damien Gardner Jnr Sent: Wednesday, 4 March 2015 5:31 PM To: MikroTik Australia Public List Subject: Re: [MT-AU Public] CCR1009 crashing - how to debug?
Thanks all,
What an horrendous day! Seems that from Xenserver 5.6 to 6.2, they lost the ability to pass an ethernet port straight to a VM, and have all the VLAN's left intact.
And then it seems that DL360G3's don't boot from USB.
Ended up installing ESXi on a spare 2950 II, and now have routeros installed on that.
Everything is working.. Except ipv6.
Can't quite figure this one out, hoping someone may have an idea..
I can't bring up BGP to either upstream gateway though. (V4 over the same vlans works fine..)
And a manual default route added then shows as unreachable: [admin@MikroTik] > /ipv6 route print detail Flags: X - disabled, A - active, D - dynamic, C - connect, S - static, r - rip, o - ospf, b - bgp, U - unreachable 0 S dst-address=::/0 gateway=2400:d400:1:ffff:ffff:: gateway-status=2400:d400:1:ffff:ffff:: unreachable distance=1 scope=30 target-scope=10
But I can ping the gateways:
[admin@MikroTik] > /ping 2400:d400:1:ffff:ffff:: SEQ HOST SIZE TTL TIME STATUS
0 2400:d400:1:ffff:ffff:: 56 255 0ms echo reply
1 2400:d400:1:ffff:ffff:: 56 255 0ms echo reply
sent=2 received=2 packet-loss=0% min-rtt=0ms avg-rtt=0ms max-rtt=0ms
Any idea what on earth i've missed? I basically just copy and pasted all the config, after manually adding all the vlan interfaces.
Thanks,
Damien
On 4 March 2015 at 13:26, Alen Orsolic <alen@duxtel.com> wrote:
Forgot to mention, reboot the router (e.g. system reboot) - run netinstall and wait for router to connect, then follow usual process. :-)
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Damien Gardner Jnr Sent: Wednesday, 4 March 2015 12:56 PM To: MikroTik Australia Public List Subject: Re: [MT-AU Public] CCR1009 crashing - how to debug?
Thanks Paul,
Figured it out.. There is no reset button... I'm not sure if it was never installed, or maybe it's floating around the motherboard, and is why I keep having issues with this router ;)
Running up a VM now and repatching my transit links!
On 4 March 2015 at 12:52, Paul Julian <paul@oxygennetworks.com.au> wrote:
> Should be able to netinstall everything I thought, there has to be a > way to reflash them and that would be it. > > They can be finicky though, keep persisting..... > > Regards > Paul > > -----Original Message----- > From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf > Of Damien Gardner Jnr > Sent: Wednesday, 4 March 2015 12:43 PM > To: MikroTik Australia Public List > Subject: Re: [MT-AU Public] CCR1009 crashing - how to debug? > > Dumb question guys, but is it POSSIBLE to netinstall a ccr1009? I > have a network cable plugged into eth8, and the other end into my > macbook. I have ethernet port bridged to a windows VM running > netinstall. I remove power from the CCR, hold in the reset button, > and power on the CCR, and then let go the reset button, and it > proceeds to boot normally :( > > Any ideas? :) > > On 4 March 2015 at 11:21, Alex Samad - Yieldbroker < > Alex.Samad@yieldbroker.com> wrote: > > > Just stating the obvious, if it is a flash issue, running for ??? > > weeks before hand and then multiple reboots. Not sure I would > > trust it if I got it back up anyway. > > > > The VM option sounds good. > > > > A > > > > > -----Original Message----- > > > From: Public [mailto:public-bounces@talk.mikrotik.com.au] On > > > Behalf Of Stavros Patiniotis > > > Sent: Wednesday, 4 March 2015 10:49 AM > > > To: 'MikroTik Australia Public List' > > > Subject: Re: [MT-AU Public] CCR1009 crashing - how to debug? > > > > > > > My CCR1009 rebooted 6 times overnight. I thought maybe it was > > > > a problem > > > with 6.25, so upgraded to 6.27. That was > a bad idea, as it > > > took a > > remote > > > hands power cycle to get back into it. I then did a downgrade > > > (which > > took it > > > all the way > > > > > > Try upgrading the firmware - had success with this before. > > > > > > system routerboard upgrade > > > > > > Stavros > > > > > > > > > _______________________________________________ > > > Public mailing list > > > Public@talk.mikrotik.com.au > > > http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik. > > > co > > > m.au > > > > _______________________________________________ > > Public mailing list > > Public@talk.mikrotik.com.au > > http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. > > au > > > > > > -- > > Damien Gardner Jnr > VK2TDG. Dip EE. GradIEAust > rendrag@rendrag.net - http://www.rendrag.net/ > -- > We rode on the winds of the rising storm, We ran to the sounds of thunder. > We danced among the lightning bolts, and tore the world asunder > _______________________________________________ > Public mailing list > Public@talk.mikrotik.com.au > http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. > au > > > _______________________________________________ > Public mailing list > Public@talk.mikrotik.com.au > http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. > au >
--
Damien Gardner Jnr VK2TDG. Dip EE. GradIEAust rendrag@rendrag.net - http://www.rendrag.net/ -- We rode on the winds of the rising storm, We ran to the sounds of thunder. We danced among the lightning bolts, and tore the world asunder _______________________________________________ Public mailing list Public@talk.mikrotik.com.au
http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.
au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au
http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.
au
--
Damien Gardner Jnr VK2TDG. Dip EE. GradIEAust rendrag@rendrag.net - http://www.rendrag.net/ -- We rode on the winds of the rising storm, We ran to the sounds of thunder. We danced among the lightning bolts, and tore the world asunder _______________________________________________ Public mailing list Public@talk.mikrotik.com.au
http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au
http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
--
Damien Gardner Jnr VK2TDG. Dip EE. GradIEAust rendrag@rendrag.net - http://www.rendrag.net/ -- We rode on the winds of the rising storm, We ran to the sounds of thunder. We danced among the lightning bolts, and tore the world asunder
--
Damien Gardner Jnr VK2TDG. Dip EE. GradIEAust rendrag@rendrag.net - http://www.rendrag.net/ -- We rode on the winds of the rising storm, We ran to the sounds of thunder. We danced among the lightning bolts, and tore the world asunder
-- Damien Gardner Jnr VK2TDG. Dip EE. GradIEAust rendrag@rendrag.net - http://www.rendrag.net/ -- We rode on the winds of the rising storm, We ran to the sounds of thunder. We danced among the lightning bolts, and tore the world asunder