It's an ASA5520, last time I looked it didn't have it ..
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Tim Warnock Sent: Sunday, 1 February 2015 6:59 PM To: MikroTik Australia Public List Subject: Re: [MT-AU Public] BFD + OSPF + ROS and BFD + BGP + ROS
Get a decent IOS for the cisco, then it should do BFD.
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Alex Samad - Yieldbroker Sent: Sunday, 1 February 2015 5:43 PM To: MikroTik Australia Public List Subject: Re: [MT-AU Public] BFD + OSPF + ROS and BFD + BGP + ROS
Hi
Did some more reading, think I am happy with the BGP side of things.
The ospf is where I am more worried.
I have a vlan my backbone that has 9 OSPF routers all ROS and 1 cisco
There cisco doesn't do BFD. I would like to turn on BFD, but I want to turn it off for the cisco node..
Am I just going to end up with my ROS boxes flapping because the cisco isn't sending BFD ??
A
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Andrew Thrift Sent: Saturday, 31 January 2015 7:42 PM To: MikroTik Australia Public List Subject: Re: [MT-AU Public] BFD + OSPF + ROS and BFD + BGP + ROS
Hi Alex,
BFD will only become active after a BGP or OSPF "session" is successfully established. With BGP it is configured per-peer. With OSPF it is configured per-interface.
If you are running point-to-point links e.g. only two devices talking OSPF then just turn it on for those "interfaces". If you have multiple neighbours on an interface, BFD will only work to the other neighbours that have it configured.
I hope that answers your question.
Regards,
Andrew
On Fri, Jan 30, 2015 at 11:59 AM, Alex Samad - Yieldbroker < Alex.Samad@yieldbroker.com> wrote:
Hi
I have asked this question on the forums but got no reply
I want to run BFD and OSPF together. I have a few routers that have multiple legs of OSPF, but I can't run BFD on some legs, because I have some legacy cisco equipment that doesn't do BFD (ASA5520 8.5).
Can I limit BFD to specific legs of OSPF determined network interface Can I limit BFD support on BGP by specific peers even if I have multiple peers on the same interface, last one can I have multiple BGP + BFD peers on the same interface ???
A
Alex Samad | Network And System Manager | Yieldbroker * +61 2 9994 2893 | ( +61 438 838 143 | * alex.samad@yieldbroker.com <mailto:alex.samad@yieldbroker.com>
This email is confidential and intended for the addressee only. If you may have received this email in error please delete it and notify the sender immediately. Recipients should not forward, disclose, distribute or copy this e-mail or any attachments in whole or part without the express permission of the sender. Views expressed in this message are those of the individual sender, except where they are specifically stated to be those of Yieldbroker. Yieldbroker accepts no liability for the content of this email, or for the consequences of any actions taken on the basis of the information provided, unless that information is subsequently confirmed in writing. Yieldbroker can not guarantee the integrity of this communication and shall not be liable for e-mail which may be intercepted, corrupted, lost, spoofed, delayed, incomplete, or virus infected.
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.co m.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au