Thanks all, What an horrendous day! Seems that from Xenserver 5.6 to 6.2, they lost the ability to pass an ethernet port straight to a VM, and have all the VLAN's left intact. And then it seems that DL360G3's don't boot from USB. Ended up installing ESXi on a spare 2950 II, and now have routeros installed on that. Everything is working.. Except ipv6. Can't quite figure this one out, hoping someone may have an idea.. I can't bring up BGP to either upstream gateway though. (V4 over the same vlans works fine..) And a manual default route added then shows as unreachable: [admin@MikroTik] > /ipv6 route print detail Flags: X - disabled, A - active, D - dynamic, C - connect, S - static, r - rip, o - ospf, b - bgp, U - unreachable 0 S dst-address=::/0 gateway=2400:d400:1:ffff:ffff:: gateway-status=2400:d400:1:ffff:ffff:: unreachable distance=1 scope=30 target-scope=10 But I can ping the gateways: [admin@MikroTik] > /ping 2400:d400:1:ffff:ffff:: SEQ HOST SIZE TTL TIME STATUS 0 2400:d400:1:ffff:ffff:: 56 255 0ms echo reply 1 2400:d400:1:ffff:ffff:: 56 255 0ms echo reply sent=2 received=2 packet-loss=0% min-rtt=0ms avg-rtt=0ms max-rtt=0ms Any idea what on earth i've missed? I basically just copy and pasted all the config, after manually adding all the vlan interfaces. Thanks, Damien On 4 March 2015 at 13:26, Alen Orsolic <alen@duxtel.com> wrote:
Forgot to mention, reboot the router (e.g. system reboot) - run netinstall and wait for router to connect, then follow usual process. :-)
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Damien Gardner Jnr Sent: Wednesday, 4 March 2015 12:56 PM To: MikroTik Australia Public List Subject: Re: [MT-AU Public] CCR1009 crashing - how to debug?
Thanks Paul,
Figured it out.. There is no reset button... I'm not sure if it was never installed, or maybe it's floating around the motherboard, and is why I keep having issues with this router ;)
Running up a VM now and repatching my transit links!
On 4 March 2015 at 12:52, Paul Julian <paul@oxygennetworks.com.au> wrote:
Should be able to netinstall everything I thought, there has to be a way to reflash them and that would be it.
They can be finicky though, keep persisting.....
Regards Paul
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Damien Gardner Jnr Sent: Wednesday, 4 March 2015 12:43 PM To: MikroTik Australia Public List Subject: Re: [MT-AU Public] CCR1009 crashing - how to debug?
Dumb question guys, but is it POSSIBLE to netinstall a ccr1009? I have a network cable plugged into eth8, and the other end into my macbook. I have ethernet port bridged to a windows VM running netinstall. I remove power from the CCR, hold in the reset button, and power on the CCR, and then let go the reset button, and it proceeds to boot normally :(
Any ideas? :)
On 4 March 2015 at 11:21, Alex Samad - Yieldbroker < Alex.Samad@yieldbroker.com> wrote:
Just stating the obvious, if it is a flash issue, running for ??? weeks before hand and then multiple reboots. Not sure I would trust it if I got it back up anyway.
The VM option sounds good.
A
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Stavros Patiniotis Sent: Wednesday, 4 March 2015 10:49 AM To: 'MikroTik Australia Public List' Subject: Re: [MT-AU Public] CCR1009 crashing - how to debug?
My CCR1009 rebooted 6 times overnight. I thought maybe it was a problem with 6.25, so upgraded to 6.27. That was > a bad idea, as it took a remote hands power cycle to get back into it. I then did a downgrade (which took it all the way
Try upgrading the firmware - had success with this before.
system routerboard upgrade
Stavros
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik. co m.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
--
Damien Gardner Jnr VK2TDG. Dip EE. GradIEAust rendrag@rendrag.net - http://www.rendrag.net/ -- We rode on the winds of the rising storm, We ran to the sounds of thunder. We danced among the lightning bolts, and tore the world asunder _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
--
Damien Gardner Jnr VK2TDG. Dip EE. GradIEAust rendrag@rendrag.net - http://www.rendrag.net/ -- We rode on the winds of the rising storm, We ran to the sounds of thunder. We danced among the lightning bolts, and tore the world asunder _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
-- Damien Gardner Jnr VK2TDG. Dip EE. GradIEAust rendrag@rendrag.net - http://www.rendrag.net/ -- We rode on the winds of the rising storm, We ran to the sounds of thunder. We danced among the lightning bolts, and tore the world asunder