Hi Folks, A few months back, I asked for opinions on a good adsl modem to use a bridge for MikroTik PPPoE. With increase in prevalence of VDSL services (especially with #nbwhen ;) does anyone have some opinion of readily available and 'good' (not necessarily cheap ;) vdsl modems? Cheers! Mike.
Hi Mike, I have been using the Draytek Vigor130 with the modem4 firmware on NBN FTTN. I would be interested in what other options people are uaing and if they get different sync speeds on the same service. Andrew On 20/05/2016 4:33 PM, "Mike Everest" <mike@duxtel.com> wrote:
Hi Folks,
A few months back, I asked for opinions on a good adsl modem to use a bridge for MikroTik PPPoE.
With increase in prevalence of VDSL services (especially with #nbwhen ;) does anyone have some opinion of readily available and 'good' (not necessarily cheap ;) vdsl modems?
Cheers!
Mike.
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
Hi Mike, Have you looked at this page? http://whirlpool.net.au/wiki/fttn_registered_modem_router I really want to see if one of these work, but haven't investigated suppliers or anything yet: http://www.metanoia-comm.com/product_d.php?id=21 An SFP module as a VDSL modem sounds very tidy - just drop one in an RB2011 and away you go! Regards, Philip Loenneker | Network Engineer | TasmaNet -----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Mike Everest Sent: Friday, 20 May 2016 4:33 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: [MT-AU Public] VDSL modems Hi Folks, A few months back, I asked for opinions on a good adsl modem to use a bridge for MikroTik PPPoE. With increase in prevalence of VDSL services (especially with #nbwhen ;) does anyone have some opinion of readily available and 'good' (not necessarily cheap ;) vdsl modems? Cheers! Mike. _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
I contacted Mikrotik about that back in March. Their response was: "We are not planning to manufacture such SFP modules in near future." -----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Philip Loenneker Sent: Friday, 20 May 2016 14:42 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems Hi Mike, Have you looked at this page? http://whirlpool.net.au/wiki/fttn_registered_modem_router I really want to see if one of these work, but haven't investigated suppliers or anything yet: http://www.metanoia-comm.com/product_d.php?id=21 An SFP module as a VDSL modem sounds very tidy - just drop one in an RB2011 and away you go! Regards, Philip Loenneker | Network Engineer | TasmaNet -----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Mike Everest Sent: Friday, 20 May 2016 4:33 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: [MT-AU Public] VDSL modems Hi Folks, A few months back, I asked for opinions on a good adsl modem to use a bridge for MikroTik PPPoE. With increase in prevalence of VDSL services (especially with #nbwhen ;) does anyone have some opinion of readily available and 'good' (not necessarily cheap ;) vdsl modems? Cheers! Mike. _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
Hi Russell, The Metanoia link I provided is to a VDSL2 SFP module, one that is already being manufactured - I wasn't suggesting that Mikrotik should make one, I was pointing out that one exists :) Regards, Philip Loenneker | Network Engineer | TasmaNet -----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Russell Hurren Sent: Friday, 20 May 2016 4:48 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems I contacted Mikrotik about that back in March. Their response was: "We are not planning to manufacture such SFP modules in near future." -----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Philip Loenneker Sent: Friday, 20 May 2016 14:42 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems Hi Mike, Have you looked at this page? http://whirlpool.net.au/wiki/fttn_registered_modem_router I really want to see if one of these work, but haven't investigated suppliers or anything yet: http://www.metanoia-comm.com/product_d.php?id=21 An SFP module as a VDSL modem sounds very tidy - just drop one in an RB2011 and away you go! Regards, Philip Loenneker | Network Engineer | TasmaNet -----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Mike Everest Sent: Friday, 20 May 2016 4:33 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: [MT-AU Public] VDSL modems Hi Folks, A few months back, I asked for opinions on a good adsl modem to use a bridge for MikroTik PPPoE. With increase in prevalence of VDSL services (especially with #nbwhen ;) does anyone have some opinion of readily available and 'good' (not necessarily cheap ;) vdsl modems? Cheers! Mike. _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
Hi Philip Have a read of http://forum.mikrotik.com/viewtopic.php?f=3&t=104109 My understanding is that the Metanoia product isn't complete but they'd sell it to an OEM who can produce a final product. At the very least it'd need to be supported in RouterOS. I emailed the link to the module to Mikrotik, and they weren't at all interested unfortunately. Regards Russell -----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Philip Loenneker Sent: Saturday, 21 May 2016 10:40 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems Hi Russell, The Metanoia link I provided is to a VDSL2 SFP module, one that is already being manufactured - I wasn't suggesting that Mikrotik should make one, I was pointing out that one exists :) Regards, Philip Loenneker | Network Engineer | TasmaNet -----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Russell Hurren Sent: Friday, 20 May 2016 4:48 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems I contacted Mikrotik about that back in March. Their response was: "We are not planning to manufacture such SFP modules in near future." -----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Philip Loenneker Sent: Friday, 20 May 2016 14:42 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems Hi Mike, Have you looked at this page? http://whirlpool.net.au/wiki/fttn_registered_modem_router I really want to see if one of these work, but haven't investigated suppliers or anything yet: http://www.metanoia-comm.com/product_d.php?id=21 An SFP module as a VDSL modem sounds very tidy - just drop one in an RB2011 and away you go! Regards, Philip Loenneker | Network Engineer | TasmaNet -----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Mike Everest Sent: Friday, 20 May 2016 4:33 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: [MT-AU Public] VDSL modems Hi Folks, A few months back, I asked for opinions on a good adsl modem to use a bridge for MikroTik PPPoE. With increase in prevalence of VDSL services (especially with #nbwhen ;) does anyone have some opinion of readily available and 'good' (not necessarily cheap ;) vdsl modems? Cheers! Mike. _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
Who can blame them. The regulatory requirements to make any sort of a/vdsl modem and get it approved in enough global markets are way to expensive for there low margin product line. Would be very very nice to see a manufacturer build that unit. I would take quite a few if it was comparable with routeros Matt -- /* Matt Perkins Direct 1300 137 379 Spectrum Networks Ptd. Ltd. Office 1300 133 299 matt@spectrum.com.au Fax 1300 133 255 Level 6, 350 George Street Sydney 2000 SIP 1300137379@sip.spectrum.com.au Google Talk MattAPerkins@gmail.com PGP/GNUPG Public Key can be found at http://pgp.mit.edu */
On 21 May 2016, at 1:24 PM, Russell Hurren <russell@zeropointnetworks.com> wrote:
Hi Philip
Have a read of http://forum.mikrotik.com/viewtopic.php?f=3&t=104109
My understanding is that the Metanoia product isn't complete but they'd sell it to an OEM who can produce a final product. At the very least it'd need to be supported in RouterOS. I emailed the link to the module to Mikrotik, and they weren't at all interested unfortunately.
Regards
Russell
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Philip Loenneker Sent: Saturday, 21 May 2016 10:40 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Hi Russell,
The Metanoia link I provided is to a VDSL2 SFP module, one that is already being manufactured - I wasn't suggesting that Mikrotik should make one, I was pointing out that one exists :)
Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Russell Hurren Sent: Friday, 20 May 2016 4:48 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
I contacted Mikrotik about that back in March. Their response was:
"We are not planning to manufacture such SFP modules in near future."
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Philip Loenneker Sent: Friday, 20 May 2016 14:42 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Hi Mike,
Have you looked at this page? http://whirlpool.net.au/wiki/fttn_registered_modem_router
I really want to see if one of these work, but haven't investigated suppliers or anything yet: http://www.metanoia-comm.com/product_d.php?id=21
An SFP module as a VDSL modem sounds very tidy - just drop one in an RB2011 and away you go!
Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Mike Everest Sent: Friday, 20 May 2016 4:33 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: [MT-AU Public] VDSL modems
Hi Folks,
A few months back, I asked for opinions on a good adsl modem to use a bridge for MikroTik PPPoE.
With increase in prevalence of VDSL services (especially with #nbwhen ;) does anyone have some opinion of readily available and 'good' (not necessarily cheap ;) vdsl modems?
Cheers!
Mike.
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
Thanks Russell - I wasn't aware that it was only a chipset, not an actual product you could already buy. I think we would purchase quite a few if they became available. If anyone happens to see these available, please share on this list :) Regards, Philip Loenneker | Network Engineer | TasmaNet -----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Matt Perkins Sent: Saturday, 21 May 2016 1:32 PM To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems Who can blame them. The regulatory requirements to make any sort of a/vdsl modem and get it approved in enough global markets are way to expensive for there low margin product line. Would be very very nice to see a manufacturer build that unit. I would take quite a few if it was comparable with routeros Matt -- /* Matt Perkins Direct 1300 137 379 Spectrum Networks Ptd. Ltd. Office 1300 133 299 matt@spectrum.com.au Fax 1300 133 255 Level 6, 350 George Street Sydney 2000 SIP 1300137379@sip.spectrum.com.au Google Talk MattAPerkins@gmail.com PGP/GNUPG Public Key can be found at http://pgp.mit.edu */
On 21 May 2016, at 1:24 PM, Russell Hurren <russell@zeropointnetworks.com> wrote:
Hi Philip
Have a read of http://forum.mikrotik.com/viewtopic.php?f=3&t=104109
My understanding is that the Metanoia product isn't complete but they'd sell it to an OEM who can produce a final product. At the very least it'd need to be supported in RouterOS. I emailed the link to the module to Mikrotik, and they weren't at all interested unfortunately.
Regards
Russell
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Philip Loenneker Sent: Saturday, 21 May 2016 10:40 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Hi Russell,
The Metanoia link I provided is to a VDSL2 SFP module, one that is already being manufactured - I wasn't suggesting that Mikrotik should make one, I was pointing out that one exists :)
Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Russell Hurren Sent: Friday, 20 May 2016 4:48 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
I contacted Mikrotik about that back in March. Their response was:
"We are not planning to manufacture such SFP modules in near future."
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Philip Loenneker Sent: Friday, 20 May 2016 14:42 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Hi Mike,
Have you looked at this page? http://whirlpool.net.au/wiki/fttn_registered_modem_router
I really want to see if one of these work, but haven't investigated suppliers or anything yet: http://www.metanoia-comm.com/product_d.php?id=21
An SFP module as a VDSL modem sounds very tidy - just drop one in an RB2011 and away you go!
Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Mike Everest Sent: Friday, 20 May 2016 4:33 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: [MT-AU Public] VDSL modems
Hi Folks,
A few months back, I asked for opinions on a good adsl modem to use a bridge for MikroTik PPPoE.
With increase in prevalence of VDSL services (especially with #nbwhen ;) does anyone have some opinion of readily available and 'good' (not necessarily cheap ;) vdsl modems?
Cheers!
Mike.
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
There are rumours that IgniteNet will produce VDSL SFP modules based off the Metanoia reference design. Only time will tell if they do or not. On 21/05/2016 5:52 pm, "Philip Loenneker" <Philip.Loenneker@tasmanet.com.au> wrote:
Thanks Russell - I wasn't aware that it was only a chipset, not an actual product you could already buy.
I think we would purchase quite a few if they became available. If anyone happens to see these available, please share on this list :)
Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Matt Perkins Sent: Saturday, 21 May 2016 1:32 PM To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Who can blame them. The regulatory requirements to make any sort of a/vdsl modem and get it approved in enough global markets are way to expensive for there low margin product line.
Would be very very nice to see a manufacturer build that unit. I would take quite a few if it was comparable with routeros
Matt
-- /* Matt Perkins Direct 1300 137 379 Spectrum Networks Ptd. Ltd. Office 1300 133 299 matt@spectrum.com.au Fax 1300 133 255 Level 6, 350 George Street Sydney 2000 SIP 1300137379@sip.spectrum.com.au Google Talk MattAPerkins@gmail.com PGP/GNUPG Public Key can be found at http://pgp.mit.edu */
On 21 May 2016, at 1:24 PM, Russell Hurren < russell@zeropointnetworks.com> wrote:
Hi Philip
Have a read of http://forum.mikrotik.com/viewtopic.php?f=3&t=104109
My understanding is that the Metanoia product isn't complete but they'd sell it to an OEM who can produce a final product. At the very least it'd need to be supported in RouterOS. I emailed the link to the module to Mikrotik, and they weren't at all interested unfortunately.
Regards
Russell
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Philip Loenneker Sent: Saturday, 21 May 2016 10:40 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Hi Russell,
The Metanoia link I provided is to a VDSL2 SFP module, one that is already being manufactured - I wasn't suggesting that Mikrotik should make one, I was pointing out that one exists :)
Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Russell Hurren Sent: Friday, 20 May 2016 4:48 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
I contacted Mikrotik about that back in March. Their response was:
"We are not planning to manufacture such SFP modules in near future."
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Philip Loenneker Sent: Friday, 20 May 2016 14:42 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Hi Mike,
Have you looked at this page? http://whirlpool.net.au/wiki/fttn_registered_modem_router
I really want to see if one of these work, but haven't investigated suppliers or anything yet: http://www.metanoia-comm.com/product_d.php?id=21
An SFP module as a VDSL modem sounds very tidy - just drop one in an RB2011 and away you go!
Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Mike Everest Sent: Friday, 20 May 2016 4:33 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: [MT-AU Public] VDSL modems
Hi Folks,
A few months back, I asked for opinions on a good adsl modem to use a bridge for MikroTik PPPoE.
With increase in prevalence of VDSL services (especially with #nbwhen ;) does anyone have some opinion of readily available and 'good' (not necessarily cheap ;) vdsl modems?
Cheers!
Mike.
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
It's been a few months since the last post. Does anyone have anything new to say on NBN VDSL modems or improvements with firmware updates for units discussed above - like the Vigor 130? On 23 May 2016 at 19:17, Andrew Thrift <andrew@networklabs.co.nz> wrote:
There are rumours that IgniteNet will produce VDSL SFP modules based off the Metanoia reference design.
Only time will tell if they do or not. On 21/05/2016 5:52 pm, "Philip Loenneker" <Philip.Loenneker@tasmanet. com.au> wrote:
Thanks Russell - I wasn't aware that it was only a chipset, not an actual product you could already buy.
I think we would purchase quite a few if they became available. If anyone happens to see these available, please share on this list :)
Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Matt Perkins Sent: Saturday, 21 May 2016 1:32 PM To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Who can blame them. The regulatory requirements to make any sort of a/vdsl modem and get it approved in enough global markets are way to expensive for there low margin product line.
Would be very very nice to see a manufacturer build that unit. I would take quite a few if it was comparable with routeros
Matt
-- /* Matt Perkins Direct 1300 137 379 Spectrum Networks Ptd. Ltd. Office 1300 133 299 matt@spectrum.com.au Fax 1300 133 255 Level 6, 350 George Street Sydney 2000 SIP 1300137379@sip.spectrum.com.au Google Talk MattAPerkins@gmail.com PGP/GNUPG Public Key can be found at http://pgp.mit.edu */
On 21 May 2016, at 1:24 PM, Russell Hurren < russell@zeropointnetworks.com> wrote:
Hi Philip
Have a read of http://forum.mikrotik.com/viewtopic.php?f=3&t=104109
My understanding is that the Metanoia product isn't complete but they'd sell it to an OEM who can produce a final product. At the very least it'd need to be supported in RouterOS. I emailed the link to the module to Mikrotik, and they weren't at all interested unfortunately.
Regards
Russell
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Philip Loenneker Sent: Saturday, 21 May 2016 10:40 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Hi Russell,
The Metanoia link I provided is to a VDSL2 SFP module, one that is already being manufactured - I wasn't suggesting that Mikrotik should make one, I was pointing out that one exists :)
Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Russell Hurren Sent: Friday, 20 May 2016 4:48 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
I contacted Mikrotik about that back in March. Their response was:
"We are not planning to manufacture such SFP modules in near future."
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Philip Loenneker Sent: Friday, 20 May 2016 14:42 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Hi Mike,
Have you looked at this page? http://whirlpool.net.au/wiki/fttn_registered_modem_router
I really want to see if one of these work, but haven't investigated suppliers or anything yet: http://www.metanoia-comm.com/product_d.php?id=21
An SFP module as a VDSL modem sounds very tidy - just drop one in an RB2011 and away you go!
Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Mike Everest Sent: Friday, 20 May 2016 4:33 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: [MT-AU Public] VDSL modems
Hi Folks,
A few months back, I asked for opinions on a good adsl modem to use a bridge for MikroTik PPPoE.
With increase in prevalence of VDSL services (especially with #nbwhen ;) does anyone have some opinion of readily available and 'good' (not necessarily cheap ;) vdsl modems?
Cheers!
Mike.
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
--
I haven't tried it yet, but Internode have released a bridge-mode firmware for the TG-1 https://forums.whirlpool.net.au/forum-replies.cfm?t=2472057&p=3#r42 Matt. On 1/09/2016 10:57 AM, Jason Hecker (Up & Running Tech) wrote:
It's been a few months since the last post. Does anyone have anything new to say on NBN VDSL modems or improvements with firmware updates for units discussed above - like the Vigor 130?
On 23 May 2016 at 19:17, Andrew Thrift <andrew@networklabs.co.nz> wrote:
There are rumours that IgniteNet will produce VDSL SFP modules based off the Metanoia reference design.
Only time will tell if they do or not. On 21/05/2016 5:52 pm, "Philip Loenneker" <Philip.Loenneker@tasmanet. com.au> wrote:
Thanks Russell - I wasn't aware that it was only a chipset, not an actual product you could already buy.
I think we would purchase quite a few if they became available. If anyone happens to see these available, please share on this list :)
Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Matt Perkins Sent: Saturday, 21 May 2016 1:32 PM To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Who can blame them. The regulatory requirements to make any sort of a/vdsl modem and get it approved in enough global markets are way to expensive for there low margin product line.
Would be very very nice to see a manufacturer build that unit. I would take quite a few if it was comparable with routeros
Matt
-- /* Matt Perkins Direct 1300 137 379 Spectrum Networks Ptd. Ltd. Office 1300 133 299 matt@spectrum.com.au Fax 1300 133 255 Level 6, 350 George Street Sydney 2000 SIP 1300137379@sip.spectrum.com.au Google Talk MattAPerkins@gmail.com PGP/GNUPG Public Key can be found at http://pgp.mit.edu */
On 21 May 2016, at 1:24 PM, Russell Hurren < russell@zeropointnetworks.com> wrote: Hi Philip
Have a read of http://forum.mikrotik.com/viewtopic.php?f=3&t=104109
My understanding is that the Metanoia product isn't complete but they'd sell it to an OEM who can produce a final product. At the very least it'd need to be supported in RouterOS. I emailed the link to the module to Mikrotik, and they weren't at all interested unfortunately. Regards
Russell
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Philip Loenneker Sent: Saturday, 21 May 2016 10:40 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Hi Russell,
The Metanoia link I provided is to a VDSL2 SFP module, one that is already being manufactured - I wasn't suggesting that Mikrotik should make one, I was pointing out that one exists :)
Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Russell Hurren Sent: Friday, 20 May 2016 4:48 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
I contacted Mikrotik about that back in March. Their response was:
"We are not planning to manufacture such SFP modules in near future."
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Philip Loenneker Sent: Friday, 20 May 2016 14:42 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Hi Mike,
Have you looked at this page? http://whirlpool.net.au/wiki/fttn_registered_modem_router
I really want to see if one of these work, but haven't investigated suppliers or anything yet: http://www.metanoia-comm.com/product_d.php?id=21
An SFP module as a VDSL modem sounds very tidy - just drop one in an RB2011 and away you go! Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Mike Everest Sent: Friday, 20 May 2016 4:33 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: [MT-AU Public] VDSL modems
Hi Folks,
A few months back, I asked for opinions on a good adsl modem to use a bridge for MikroTik PPPoE. With increase in prevalence of VDSL services (especially with #nbwhen ;) does anyone have some opinion of readily available and 'good' (not necessarily cheap ;) vdsl modems? Cheers!
Mike.
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
-- _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
I see Netgear have a basic DM200 unit which is a modem only capable of bridging for about $80. Whirlpool shows you have to put firmware 1.0.0.36 on first otherwise it'll lock the port. I think it might be a while before decent modems that have good sync and don't crash once a day come out.... On 1 September 2016 at 09:08, Matt Richards <matt@shakesbeare.com> wrote:
I haven't tried it yet, but Internode have released a bridge-mode firmware for the TG-1 https://forums.whirlpool.net.au/forum-replies.cfm?t=2472057&p=3#r42
Matt.
On 1/09/2016 10:57 AM, Jason Hecker (Up & Running Tech) wrote:
It's been a few months since the last post. Does anyone have anything new to say on NBN VDSL modems or improvements with firmware updates for units discussed above - like the Vigor 130?
On 23 May 2016 at 19:17, Andrew Thrift <andrew@networklabs.co.nz> wrote:
There are rumours that IgniteNet will produce VDSL SFP modules based off
the Metanoia reference design.
Only time will tell if they do or not. On 21/05/2016 5:52 pm, "Philip Loenneker" <Philip.Loenneker@tasmanet. com.au> wrote:
Thanks Russell - I wasn't aware that it was only a chipset, not an actual
product you could already buy.
I think we would purchase quite a few if they became available. If anyone happens to see these available, please share on this list :)
Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Matt Perkins Sent: Saturday, 21 May 2016 1:32 PM To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Who can blame them. The regulatory requirements to make any sort of
a/vdsl
modem and get it approved in enough global markets are way to expensive
for
there low margin product line.
Would be very very nice to see a manufacturer build that unit. I would take quite a few if it was comparable with routeros
Matt
-- /* Matt Perkins Direct 1300 137 379 Spectrum Networks Ptd. Ltd. Office 1300 133 299 matt@spectrum.com.au Fax 1300 133 255 Level 6, 350 George Street Sydney 2000 SIP 1300137379@sip.spectrum.com.au Google Talk MattAPerkins@gmail.com PGP/GNUPG Public Key can be found at http://pgp.mit.edu */
On 21 May 2016, at 1:24 PM, Russell Hurren <
russell@zeropointnetworks.com> wrote:
Hi Philip
Have a read of http://forum.mikrotik.com/viewtopic.php?f=3&t=104109
My understanding is that the Metanoia product isn't complete but they'd
sell it to an OEM who can produce a final product. At the very least it'd need to be supported in RouterOS. I emailed the link to the module to Mikrotik, and they weren't at all interested unfortunately.
Regards
Russell
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Philip Loenneker Sent: Saturday, 21 May 2016 10:40 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Hi Russell,
The Metanoia link I provided is to a VDSL2 SFP module, one that is already being manufactured - I wasn't suggesting that Mikrotik should make one, I was pointing out that one exists :)
Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Russell Hurren Sent: Friday, 20 May 2016 4:48 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
I contacted Mikrotik about that back in March. Their response was:
"We are not planning to manufacture such SFP modules in near future."
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Philip Loenneker Sent: Friday, 20 May 2016 14:42 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Hi Mike,
Have you looked at this page? http://whirlpool.net.au/wiki/fttn_registered_modem_router
I really want to see if one of these work, but haven't investigated
suppliers or anything yet:
http://www.metanoia-comm.com/product_d.php?id=21
An SFP module as a VDSL modem sounds very tidy - just drop one in an
RB2011 and away you go!
Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Mike Everest Sent: Friday, 20 May 2016 4:33 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: [MT-AU Public] VDSL modems
Hi Folks,
A few months back, I asked for opinions on a good adsl modem to use a
bridge for MikroTik PPPoE.
With increase in prevalence of VDSL services (especially with #nbwhen
;)
does anyone have some opinion of readily available and 'good' (not necessarily cheap ;) vdsl modems?
Cheers!
Mike.
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mik rotik.com.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mik rotik.com.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
-- _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
--
I've just installed a Vigor 130 at a client site. Haven't tested it in bridge mode yet (router hasn't arrived yet) but it connected to VDSL once I got the correct settings (needed a VLAN tag). The client is a friend who was willing to try something new, so we'll see how it goes. I have confirmed that it will go into bridge mode at least. Planet have a nice looking VDSL modem, but it doesn't support vectoring, so no good for NBN. -----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Jason Hecker (Up & Running Tech) Sent: Friday, 7 October 2016 03:29 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems I see Netgear have a basic DM200 unit which is a modem only capable of bridging for about $80. Whirlpool shows you have to put firmware 1.0.0.36 on first otherwise it'll lock the port. I think it might be a while before decent modems that have good sync and don't crash once a day come out.... On 1 September 2016 at 09:08, Matt Richards <matt@shakesbeare.com> wrote:
I haven't tried it yet, but Internode have released a bridge-mode firmware for the TG-1 https://forums.whirlpool.net.au/forum-replies.cfm?t=2472057&p=3#r42
Matt.
On 1/09/2016 10:57 AM, Jason Hecker (Up & Running Tech) wrote:
It's been a few months since the last post. Does anyone have anything new to say on NBN VDSL modems or improvements with firmware updates for units discussed above - like the Vigor 130?
On 23 May 2016 at 19:17, Andrew Thrift <andrew@networklabs.co.nz> wrote:
There are rumours that IgniteNet will produce VDSL SFP modules based off
the Metanoia reference design.
Only time will tell if they do or not. On 21/05/2016 5:52 pm, "Philip Loenneker" <Philip.Loenneker@tasmanet. com.au> wrote:
Thanks Russell - I wasn't aware that it was only a chipset, not an actual
product you could already buy.
I think we would purchase quite a few if they became available. If anyone happens to see these available, please share on this list :)
Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Matt Perkins Sent: Saturday, 21 May 2016 1:32 PM To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Who can blame them. The regulatory requirements to make any sort of
a/vdsl
modem and get it approved in enough global markets are way to expensive
for
there low margin product line.
Would be very very nice to see a manufacturer build that unit. I would take quite a few if it was comparable with routeros
Matt
-- /* Matt Perkins Direct 1300 137 379 Spectrum Networks Ptd. Ltd. Office 1300 133 299 matt@spectrum.com.au Fax 1300 133 255 Level 6, 350 George Street Sydney 2000 SIP 1300137379@sip.spectrum.com.au Google Talk MattAPerkins@gmail.com PGP/GNUPG Public Key can be found at http://pgp.mit.edu */
On 21 May 2016, at 1:24 PM, Russell Hurren <
russell@zeropointnetworks.com> wrote:
Hi Philip
Have a read of http://forum.mikrotik.com/viewtopic.php?f=3&t=104109
My understanding is that the Metanoia product isn't complete but they'd
sell it to an OEM who can produce a final product. At the very least it'd need to be supported in RouterOS. I emailed the link to the module to Mikrotik, and they weren't at all interested unfortunately.
Regards
Russell
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Philip Loenneker Sent: Saturday, 21 May 2016 10:40 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Hi Russell,
The Metanoia link I provided is to a VDSL2 SFP module, one that is already being manufactured - I wasn't suggesting that Mikrotik should make one, I was pointing out that one exists :)
Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Russell Hurren Sent: Friday, 20 May 2016 4:48 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
I contacted Mikrotik about that back in March. Their response was:
"We are not planning to manufacture such SFP modules in near future."
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Philip Loenneker Sent: Friday, 20 May 2016 14:42 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Hi Mike,
Have you looked at this page? http://whirlpool.net.au/wiki/fttn_registered_modem_router
I really want to see if one of these work, but haven't investigated
suppliers or anything yet:
http://www.metanoia-comm.com/product_d.php?id=21
An SFP module as a VDSL modem sounds very tidy - just drop one in an
RB2011 and away you go!
Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Mike Everest Sent: Friday, 20 May 2016 4:33 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: [MT-AU Public] VDSL modems
Hi Folks,
A few months back, I asked for opinions on a good adsl modem to use a
bridge for MikroTik PPPoE.
With increase in prevalence of VDSL services (especially with #nbwhen
;)
does anyone have some opinion of readily available and 'good' (not necessarily cheap ;) vdsl modems?
Cheers!
Mike.
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mik rotik.com.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mik rotik.com.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.co m.au
-- _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com .au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
-- _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
We use a lot of the planet VDR300N routers which are VDSL/VDSL2 and do 30a, but as Russell says they don't do vectoring, the strange thing is though that they are identical to the Netcomm and another brand which do vectoring, strange.... We have just got some of the brand new TPLink Routers which are claimed to be NBN compatible and will do everything, time will tell if they are any good. Regards PAul -----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Russell Hurren Sent: Friday, 7 October 2016 12:46 PM To: 'MikroTik Australia Public List' Subject: Re: [MT-AU Public] VDSL modems I've just installed a Vigor 130 at a client site. Haven't tested it in bridge mode yet (router hasn't arrived yet) but it connected to VDSL once I got the correct settings (needed a VLAN tag). The client is a friend who was willing to try something new, so we'll see how it goes. I have confirmed that it will go into bridge mode at least. Planet have a nice looking VDSL modem, but it doesn't support vectoring, so no good for NBN. -----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Jason Hecker (Up & Running Tech) Sent: Friday, 7 October 2016 03:29 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems I see Netgear have a basic DM200 unit which is a modem only capable of bridging for about $80. Whirlpool shows you have to put firmware 1.0.0.36 on first otherwise it'll lock the port. I think it might be a while before decent modems that have good sync and don't crash once a day come out.... On 1 September 2016 at 09:08, Matt Richards <matt@shakesbeare.com> wrote:
I haven't tried it yet, but Internode have released a bridge-mode firmware for the TG-1 https://forums.whirlpool.net.au/forum-replies.cfm?t=2472057&p=3#r42
Matt.
On 1/09/2016 10:57 AM, Jason Hecker (Up & Running Tech) wrote:
It's been a few months since the last post. Does anyone have anything new to say on NBN VDSL modems or improvements with firmware updates for units discussed above - like the Vigor 130?
On 23 May 2016 at 19:17, Andrew Thrift <andrew@networklabs.co.nz> wrote:
There are rumours that IgniteNet will produce VDSL SFP modules based off
the Metanoia reference design.
Only time will tell if they do or not. On 21/05/2016 5:52 pm, "Philip Loenneker" <Philip.Loenneker@tasmanet. com.au> wrote:
Thanks Russell - I wasn't aware that it was only a chipset, not an actual
product you could already buy.
I think we would purchase quite a few if they became available. If anyone happens to see these available, please share on this list :)
Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Matt Perkins Sent: Saturday, 21 May 2016 1:32 PM To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Who can blame them. The regulatory requirements to make any sort of
a/vdsl
modem and get it approved in enough global markets are way to expensive
for
there low margin product line.
Would be very very nice to see a manufacturer build that unit. I would take quite a few if it was comparable with routeros
Matt
-- /* Matt Perkins Direct 1300 137 379 Spectrum Networks Ptd. Ltd. Office 1300 133 299 matt@spectrum.com.au Fax 1300 133 255 Level 6, 350 George Street Sydney 2000 SIP 1300137379@sip.spectrum.com.au Google Talk MattAPerkins@gmail.com PGP/GNUPG Public Key can be found at http://pgp.mit.edu */
On 21 May 2016, at 1:24 PM, Russell Hurren <
russell@zeropointnetworks.com> wrote:
Hi Philip
Have a read of http://forum.mikrotik.com/viewtopic.php?f=3&t=104109
My understanding is that the Metanoia product isn't complete but they'd
sell it to an OEM who can produce a final product. At the very least it'd need to be supported in RouterOS. I emailed the link to the module to Mikrotik, and they weren't at all interested unfortunately.
Regards
Russell
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Philip Loenneker Sent: Saturday, 21 May 2016 10:40 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Hi Russell,
The Metanoia link I provided is to a VDSL2 SFP module, one that is already being manufactured - I wasn't suggesting that Mikrotik should make one, I was pointing out that one exists :)
Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Russell Hurren Sent: Friday, 20 May 2016 4:48 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
I contacted Mikrotik about that back in March. Their response was:
"We are not planning to manufacture such SFP modules in near future."
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Philip Loenneker Sent: Friday, 20 May 2016 14:42 To: MikroTik Australia Public List <public@talk.mikrotik.com.au> Subject: Re: [MT-AU Public] VDSL modems
Hi Mike,
Have you looked at this page? http://whirlpool.net.au/wiki/fttn_registered_modem_router
I really want to see if one of these work, but haven't investigated
suppliers or anything yet:
http://www.metanoia-comm.com/product_d.php?id=21
An SFP module as a VDSL modem sounds very tidy - just drop one in an
RB2011 and away you go!
Regards, Philip Loenneker | Network Engineer | TasmaNet
-----Original Message----- From: Public [mailto:public-bounces@talk.mikrotik.com.au] On Behalf Of Mike Everest Sent: Friday, 20 May 2016 4:33 PM To: 'MikroTik Australia Public List' <public@talk.mikrotik.com.au> Subject: [MT-AU Public] VDSL modems
Hi Folks,
A few months back, I asked for opinions on a good adsl modem to use a
bridge for MikroTik PPPoE.
With increase in prevalence of VDSL services (especially with #nbwhen
;)
does anyone have some opinion of readily available and 'good' (not necessarily cheap ;) vdsl modems?
Cheers!
Mike.
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mik rotik.com.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mik rotik.com.au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.co m.au
-- _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com .au
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com. au
-- _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au _______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
So far I have not found one which is 'good'. The Draytek Vigor 130 is 'ok'. However you MUST flash the firmware to the Vectoring-compatible one before plugging it in, or you will lock your port out. In bridge mode it does fairly well, and worked great at our previous house. Note though that it is HORRENDOUS on a short line, where it is presented with a high signal strength. It drops out every 10 mins or so at our current house (90m to the node, rather than 570m). It also syncs lower than any other modem (50/12 at the old house, compared to 60/18 on the Telstra modem and the NF4V) The Netcomm NF4V syncs at a much higher rate than the Vigor, but it randomly locks up at least once to twice a day, even in bridge mode. I've also tried a TP-Link W9970, which also syncs well, however it also locks up randomly once a day. TBH, I've actually somewhat settled on the Huawei HG630 which TPG provided, as it's quite solid. That said, I haven't actually tried it in bridge mode, as it's the only one of the above modems that I've found just simply lets you turn off NAT, put public IP's on the LAN, and then *works* as a router with no messing about. Though it doesn't support SNMP :\ I've heard good things about Fritzbox's, and may try one eventually, but for now the Huawei is doing well :) If you do try one, let me know how it goes ;) if you know anyone who wants to buy a Vigor 130, NF4v, or W9970 cheap, point them my way ;) On 20 May 2016 at 16:32, Mike Everest <mike@duxtel.com> wrote:
Hi Folks,
A few months back, I asked for opinions on a good adsl modem to use a bridge for MikroTik PPPoE.
With increase in prevalence of VDSL services (especially with #nbwhen ;) does anyone have some opinion of readily available and 'good' (not necessarily cheap ;) vdsl modems?
Cheers!
Mike.
_______________________________________________ Public mailing list Public@talk.mikrotik.com.au http://talk.mikrotik.com.au/mailman/listinfo/public_talk.mikrotik.com.au
-- Damien Gardner Jnr VK2TDG. Dip EE. GradIEAust rendrag@rendrag.net - http://www.rendrag.net/ -- We rode on the winds of the rising storm, We ran to the sounds of thunder. We danced among the lightning bolts, and tore the world asunder
participants (10)
-
Andrew Gilbett -
Andrew Thrift -
Damien Gardner Jnr -
Jason Hecker (Up & Running Tech) -
Matt Perkins -
Matt Richards -
Mike Everest -
Paul Julian -
Philip Loenneker -
Russell Hurren